Description
Sierra Flame Lynwood W76 Wood Burning Stove with Cast Iron Door, Black Colour Finish
The Sierra Flame Lynwood W76 is a welcome addition for wood burners everywhere, and is what a wood burning stove should be: efficient, low emissions, and provides great flames with a maximum viewing area.
Versatile, the Lynwood W76 wood burning stove adapts to any room and will create a cozy atmosphere in any space.
EPA 2020 certified, the Lynwood W76 wood burning stove brings warmth without compromising on air quality.
FEATURES
- 2020 EPA Compliant
- 78% Maximum Efficency
- 13,784 to 57,674 BTU/hr
- Heats up 2000 ft²
- Maximum Log size – 21″
- Massive glass for fire viewing
View Powerpoint presentation – CLICK HERE
REQUIRED ACCESSORIES
Mandatory to complete the unit: Reduce Clearance Heat Shield
DISCLAIMER :
Flames and flame colors on the website may appear differently in real life. To view the most accurate representation of the FIRE & ICE® flame and our regular flame sets, please visit your nearest dealer.
We reserve the right to update products, specifications and dimensions are subject to change. Please refer to the product manual to verify measurements and clearance requirements. All local building codes must be followed.
WARNING : California Residents – California Proposition 65
This product can expose you to chemicals including lead, that is found in some copper fittings, which is [are] know to the State of California to cause birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov
More on California Proposition 65 – CLICK HERE
Specs
W76
|
| Type |
Solid Fuel Room Heater |
| Type of Combustion |
Non-catalytic |
| Fuel Type |
Dry Cordwood (15% moisture) |
| Main Material |
Cast Iron |
| Firebox Isolation |
Vermiculite |
| Flue Exit |
6” (150 mm) Back to top connector |
| Recommended Heating Area |
450 to 2,000 ft.2 (42 to 185 m2) |
| Nominal Firebox Volume |
1.55 ft.3 (0.044 m3) |
| Maximum Burn Time 1 |
14 hours |
| Maximum Heat Output (dry cordwood) 2 |
57,700 BTU/h (16.91 kW) |
| Overall Heat Output Rate (min. to max.) 2 3 |
13,784 BTU/h to 57,684 BTU/h
(4.04 kW to 16.91 kW) |
| Average Overall Efficiency 3 |
71% (HHV) 4 76% (LHV) 5 |
| Optimum Efficiency 5 |
78% |
| Average Particulate Emissions Rate 7 |
1.81 g/h (EPA/CSA B415.1-10) |
| Average CO5 |
120 g/h |
1 Maximum Burn Time will vary depending on design of home, climate, wood type and operation.
2 Heat Out Range results are determined during specific emissions test established by the EPA.
3 As measured per CSA B415. 1-10 stack loss method. The Maximum Heat Output value is representative of a morefrequent re-fueling cycle than specified.
4 Higher Heating Value of the fuel is obtained per CSA B415. 1-10 test method.
5 Lower Heating Value of the fuel is obtained per CSA B415. 1-10 test method.
6 Optimum overall efficiency at a specific burn rate (LHV).
7This appliance is officially tested and certified by an independent agency. Particulate Emissions rate is obtained using EPA Test Method.
8 Carbon Monoxide Emissions rate results from Test Method CSA B415. 1-10
DISCLAIMER :
Flames and flame colors on the website may appear differently in real life. To view the most accurate representation of the FIRE & ICE® flame and our regular flame sets, please visit your nearest dealer.
We reserve the right to update products, specifications and dimensions are subject to change. Please refer to the product manual to verify measurements and clearance requirements. All local building codes must be followed.
WARNING : California Residents – California Proposition 65
This product can expose you to chemicals including lead, that is found in some copper fittings, which is [are] know to the State of California to cause birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov
More on California Proposition 65 – CLICK HERE
